Re: iSCSI: CmdSN during the Login phase

["Matt Wakeley" <matt_wakeley@agilent.com>]

I think it's pretty obvious that it's your option #1: (the initiator supplies
the initial CmdSN in the login PDU, and for every command PDU after that, the
CmdSN gets incremented, just like in "full feature phase")

2.10.7 CmdSN says "CmdSN is either the initial number of a session..."
[Julian, this should say "initial command number of a session"]

So, the Login PDU defines the first CmdSN.

1.2.2.1 says "Commands in transit from the initiator to the target layer are
numbered by iSCSI; the number is carried by the iSCSI PDU as CmdSN".  Text
commands are commands, so they are numbered also.

It goes on to say "CmdSN - the current command Sequence Number advanced by 1
on each command shipped except for commands marked for immediate delivery."

I agree that this needs to be cleaned up. CmdSN and StatSN should work during
login just like they do during "full feature phase" - there is no reason why
the should not, and making them always work the same removes complexity and
interoperability problems.

-Matt

"Scott M. Ferris" wrote:
> 
>   At what point during the Login Phase of a leading connection (null
> TSID) does a session exist?
> 
>   Section 2.10.7 describing CmdSN for the Login PDU indicates that
> when TSID is null, CmdSN indicates the starting Command Sequence
> number for this session.
> 
>   For interoperability, it is important to define precisely when a
> session exists, so that all initiators and targets agree on when
> CmdSNs are significant, and do not reject or ignore PDUs due to
> differing assumptions of how the CmdSN numbering should be done during
> the Login Phase.
> 
> Some of the possible choices for session start are:
> 
> 1) a session starts before the initiator sends anything, and the Login
>    PDU is the first PDU of a session.
> 
> 2) a session starts when the initiator receives a (possibly partial)
>    Login Response with an accept status class and a non-zero TSID, and
>    the next PDU sent by the initiator is the first PDU of the session,
>    which uses the same CmdSN as the Login PDU.
> 
> 3) a session starts when the initiator receives a Final Login
>    Response, and the next PDU sent by the initiator is the first PDU
>    of the session, which uses the same CmdSN as the Login PDU.
> 
>   After searching through draft 6, I was unable to find anything that
> clearly indicated which if any of the above possibilities was correct,
> or, if more than one is possible, how the initiator and target are
> supposed to determine what CmdSN numbering scheme the other side is
> using for the Login Phase.
> 
>   The UNH draft-6 initiator appears to use choice #1.  The Cisco
> draft-6 initiator and target use choice #2.  This can cause the UNH
> initiator to hang when trying to login to the Cisco target, since the
> initiator may send a Text PDU with CmdSN 2, while the target is
> waiting for a PDU with CmdSN 1.
> 
>   Section 1.2.2.2 states that "Status numbering starts after
> Login. During login, there is always only one outstanding command per
> connection and status numbering is not strictly needed but may be used
> as a sanity check."
> 
>   A similar argument could be made that CmdSN is not needed during the
> Login Phase, suggesting choice #3 may be the simplest.
> 
>   I also think section 1.2.2.2 is problematic, as it appears to
> contradict itself by saying that status numbering is not used during
> login, and then follows up saying status numbering may be used during
> login.
> 
> --
> Scott M. Ferris,
> sferris@acm.org