Re: iSCSI - Change - Login/Text commands with the binary stage code

["John Hufferd" <hufferd@us.ibm.com>]

Mark, (I attached this note to the wrong message from you previously, so
here it is attached to the approprate message)

Regardless of whether IKE and IPSec is used, you Still need iSCSI
Authentication to prevent Masquerading as various different iSCSI Initiator
Nodes.

.

.
.
.
John L. Hufferd
Senior Technical Staff Member (STSM)
IBM/SSG San Jose Ca
Main Office (408) 256-0403, Tie: 276-0403,  eFax: (408) 904-4688
Home Office (408) 997-6136
Internet address: hufferd@us.ibm.com


Mark Bakke <mbakke@cisco.com>@ece.cmu.edu on 08/30/2001 12:13:34 PM

Sent by:  owner-ips@ece.cmu.edu


To:   Bill Strahm <bill@sanera.net>
cc:   Julian Satran/Haifa/IBM@IBMIL, "Ips@Ece. Cmu. Edu" <ips@ece.cmu.edu>
Subject:  Re: iSCSI - Change - Login/Text commands with the binary stage
      code



Bill-

In Irvine, we agreed that when IPsec is enabled, IKE will be used
to do key exchange.  We also agreed on which transforms to use when
IPsec is enabled.

The key word is "enabled".  Keep in mind that there will probably
be three classes of iSCSI implementations "out there":

1. iSCSI implementations without security.  These won't be able to
   say they are "compliant", but are likely to be the majority of
   implementations, at least for a little while.  At any rate, we
   all pay our marketing folks to get us around this one.

2. iSCSI implementations with software security.  These will add
   IPsec in software for one of two reasons: either high performance
   is not required (perhaps it's designed to go over a T1 or something),
   or just so the "RFC-xxxx-compliant" bullet can be checked off on
   the list.  If it's for the first reason, IPsec will be used by
   some customers; if it's for the second reason, it will likely
   never be enabled.

3. iSCSI implementations with hardware security.  These will be
   serious implementations that include IPsec, and can perform
   well enough that a customer will want to use IPsec.  These
   implementations will enable IPsec if the customer needs it, but
   again, might not enable it if this is not a concern.

Your assumption seems to be that because we chose IPsec/IKE, that
it will always be used.  Given the implementations 1 and 2, and
some of 3, that is not always the case.

As you mentioned, when your assumptions are correct, the login
phase only has to exchange initiator and target names, and can
use AuthMethod=none if it likes.  However, those assumptions
will not always hold.

--
Mark

Bill Strahm wrote:
>
> Ok,
>
> I am confused here (or maybe it is just a lag effect for me)
>
> I thought we had decided in Irvine to use IPsec/IKE to negotiate
security.
> So basically the process is this
>
> 1) Administrator makes several entries into a Security Policy Database
> 2) An iSCSI initiator attempts to send a TCP-SYN packet to a target
machine
> 3) The IPsec packet filter detects this packet, realized there isn't a
> security association for it, and asks the Security Policy Database what
to
> do about it
> 4) The security Policy Database may determine that an IPsec SA needs to
be
> established so tells IKE to negotiate with the remote peer
> 5) An IKE negotiation proceeds until either it succeeds or fails
> 6) If it fails, packets are dropped
> 7) If it succeeds, the negotiated SAs are pushed to the IPsec packet
filters
> 8) The origional TCP-SYN packet is now sent out under the IPsec SA that
was
> negotiated.
>
> Now under this scenario there is no need for iSCSI to negotiate security
at
> all.  I DO now see the need to include an iSCSI Login phase that includes
> passing user identities across so targets and initiators can identify
> themselves, but this is over a secure link (see the above discussion) so
I
> can just put ID= Bills-iSCSI-Initiator PW=BetYouCantGuessIt and the link
> will secure it for me...
>
> Bill
> Sanera Systems Inc.
> -----Original Message-----
> From: owner-ips@ece.cmu.edu [mailto:owner-ips@ece.cmu.edu]On Behalf Of
> Julian Satran
> Sent: Wednesday, August 29, 2001 2:40 PM
> To: ips@ece.cmu.edu
> Subject: Re: iSCSI - Change - Login/Text commands with the binary stage
> code
>
> Steve,
>
> Implement and use are different terms. An administrator might set it up
not
> to use security under specific conditions.
>
> Julo
>
> Steve Senum <ssenum@cisco.com>@ece.cmu.edu on 30-08-2001 00:12:28
>
> Please respond to Steve Senum <ssenum@cisco.com>
>
> Sent by:  owner-ips@ece.cmu.edu
>
> To:   ietf-ips <ips@ece.cmu.edu>
> cc:
> Subject:  Re: iSCSI - Change - Login/Text commands with the binary stage
>       code
>
> Julian,
>
> In the following section:
>
>    If the initiator decides to forego the SecurityNegotiation stage it
>    issues the Login with the CNxSG set to LoginOperationalNegotiation in
>    the current stage and the target may replay with a Login Response
>    indicating that it is unwilling to accept the connection without
>    SecurityNegotiation and terminate the connection.
>
> This seems contrary to the requirement to implement
> authentication (at least AuthMethod=SRP).  I realize
> this could also be a configuration issue, but I wonder
> if the spec should at least strongly recommend starting
> with phase SecurityNegotiation, or better yet, make it
> a SHOULD?
>
> Regards,
> Steve Senum

--
Mark A. Bakke
Cisco Systems
mbakke@cisco.com
763.398.1054