RE: iSCSI: Implicit Termination of Tasks

["Julian Satran" <Julian_Satran@il.ibm.com>]

Noooo - it will require explaining the
whole SCSI context (ACA active, queues etc.)  And as I pointed out
in many usefull cases you don't even have to do anything.

Julo

Eddy Quicksall <eddy_quicksall@ivivity.com>

08/01/03 18:29

To	Julian Satran/Haifa/IBM@IBMIL, Black_David@emc.com
cc	david.brown@trebia.com, ips@ece.cmu.edu, owner-ips@ece.cmu.edu
Subject	RE: iSCSI: Implicit Termination of Tasks

Should this be added to the end?
"However, since the UA is set, the next command will get the UA or
ACA Active".
 
Eddy
-----Original Message-----
From: Julian Satran [mailto:Julian_Satran@il.ibm.com]
Sent: Wednesday, January 08, 2003 1:59 AM
To: Black_David@emc.com
Cc: david.brown@trebia.com; ips@ece.cmu.edu; owner-ips@ece.cmu.edu
Subject: RE: iSCSI: Implicit Termination of Tasks


How about the following text: 

If the tasks terminated in the above cases a), b, c) and d)are SCSI tasks,
they must be internally terminated with CHECK CONDITION status with a sense
key of unit attention and ASC/ASCQ values of 0x6E/0x00 (COMMAND TO LOGICAL
UNIT FAILED).  This status is only meaningful for appropriately handling
the internal SCSI state and SCSI side effects with respect to ordering
(e.g., queued commands and ACA) because this status is never communicated
back as a terminating status to the initiator. 

Please pay attention to the fact that the statement about the status not
being returned is unchanged. 

10.14.5 now reads also: 

Implicit termination of tasks

A target implicitly terminates the active tasks in three cases due to iSCSI protocol:

When a connection is implicitly or explicitly logged out with the reason code of "Close the connection" and there are active tasks allegiant to that connection.
               
When a connection fails and eventually the connection state times out (state transition M1 in Section 7.2.2 State Transition Descriptions for Initiators and Targets) and there are active tasks allegiant to that connection.
               
When a successful recovery Logout is performed while there are active tasks allegiant to that connection, and those tasks eventually time out after the Time2Wait and Time2Retain periods without allegiance reassignment.
               
When a connection is implicitly or explicitly logged out with the reason code of "Close the session" and there are active tasks in that session.
               

If the tasks terminated in any of the above cases are SCSI tasks, they must be internally terminated with CHECK CONDITION status with a sense key of unit attention and ASC/ASCQ values of 0x6E/0x00 (COMMAND TO LOGICAL UNIT FAILED).  This status is only meaningful for appropriately handling the internal SCSI state and SCSI side effects with respect to ordering (e.g., queued commands and ACA) because this status is never communicated back as a terminating status to the initiator.

Julo

Black_David@emc.com
Sent by: owner-ips@ece.cmu.edu

08/01/03 03:57

To	david.brown@trebia.com, ips@ece.cmu.edu
cc
Subject	RE: iSCSI: Implicit Termination of Tasks

Folks,

We need to drive this issue to closure.  The gory details of the
cross-initiator effects of task termination with CHECK CONDITION
are summarized in Table 25 of Section 5.9.1.2 of SAM-2, and the
next four subsections describe how this affects new tasks.  As
David Brown pointed out, the important behavior to note is that
when TST is 0, any such termination affects *all* tasks regardless
of initiator, and if it results in an ACA, that affects
*all* existing and new tasks until the ACA cleared.  FWIW, iSCSI's
requirement that autosense MUST be used eliminates the possibility
of a new task being created while CA is in effect as the CA is
immediately cleared by autosense.

Given this, especially its ACA aspects, and the fact that iSCSI needs
to support ACA, the distinction currently made in Section 6.5 between
connection closure and session closure seems wrong - I'm inclined
to agree with David Brown and Eddy Quicksall that all four cases
in Section 6.5 need to implicitly terminate the tasks with CHECK
CONDITION for consistency, and I also think that David Brown's
add text observing that there may be cross-initiator side effects
depending on how CA and ACA are handled is reasonable, but I would
limit it to about what I just wrote plus advice to consult SAM-2.

Anyone want to disagree?

Thanks,
--David


> I don't understand why the generation of CHECK CONDITIONs is immaterial
when
> a session is closed.  When a check condition generates a CA or
ACA, it can
> affect tasks from other initiators, too.  Look at the TST and
QErr bits in
> the Control mode page.
> 
> If the TST bit, in the Control mode page, is zero and the QErr data
field,
> in the same mode page, contains 01b, then a check condition causes
all
tasks
> from all initiators to be aborted.
> 
> If TST is zero and QErr is not 01b, then all tasks from other initiators
are
> temporarily blocked by a CA or ACA.  The situation in which an
ACA was
> generated and the session was closed is particularly problematic,
because
> the initiator that caused the ACA is gone.  One of the other
initiators
> would need to reset the unit, or send a PERSISTENT RESERVE OUT, to
clear
the
> ACA.
> 
> It wouldn't have done any harm to make the last paragraph of 6.5 apply
to
> clause (d), namely session closure.  It certainly would have
been helped
if
> the paragraph referred to CA and ACA explicitly.  Such a statement
would
> have made clear the underlying assumption, namely that a check condition
> never affects other initiators, as long as the target 
> implements autosense.
> 
> Bottom line: If I understand the SAM and SPC specs correctly, the
current
> draft of the iSCSI spec is incorrect.  Clause (d) of 6.5 should
cause the
> tasks to be terminated with a check condition, just like clauses (a),
(b),
> and (c).  The check condition is visible externally in two situations:
> 
> 1.  Closing a session will cause tasks from other sessions to
be aborted,
if
> QErr contains 01b and TST contains 0.
> 2.  Closing a session will cause tasks from other sessions to
be blocked,
if
> QErr contains 00b (or 011b) and TST contains 0 and any of the terminated
> commands had the NACA bit set.
> 
> dj
> 
> 
> -----Original Message-----
> From: Eddy Quicksall [mailto:Eddy_Quicksall@ivivity.com]
> Sent: Tuesday, January 07, 2003 8:52 AM
> To: 'Mallikarjun C.'; ips@ece.cmu.edu
> Subject: RE: iSCSI: Implicit Termination of Tasks
> 
> 
> If it never makes it back to the initiator, then it is an 
> implementation
> issue. As long as the target maintains all ordering 
> requirements (iSCSI out
> of order commands and SCSI queued commands), all should be 
> well and there
> would be no requirement imposed in the spec to implement this.
> 
> If would be better to have just given the paragraph below as an
> implementation note. As long as we all understand what your 
> intent was, then
> we should be OK (and you have now explained that).
> 
> Thanks
> 
> Eddy
> 
> -----Original Message-----
> From: Mallikarjun C. [mailto:cbm@rose.hp.com]
> Sent: Monday, January 06, 2003 9:15 PM
> To: Eddy_Quicksall@iVivity.com; ips@ece.cmu.edu
> Subject: Re: iSCSI: Implicit Termination of Tasks
> 
> 
> Eddy,
> 
> iSCSI's design goal was to ensure command ordering
> even in the face of errors - ultimately, we wanted the SCSI
> execution ordering to be correct while running on iSCSI.
> This should be able to be guaranteed by the iSCSI targets,
> while initiators may/may not employ command ordering.
> 
> For this to happen, iSCSI must both maintain its delivery
> ordering, and require SCSI CHECK CONDITIONs to
> be locally triggered on the target on iSCSI exception
> conditions such as connection terminations.  The CHECK
> CONDITION would then cause the ACA/persistent-UA to
> be invoked if so desired by the initiator.
> 
> This is not "a method of implementing", it's required behavior
> to meet iSCSI's architectural guarantee of command ordering.
> --
> Mallikarjun
> 
> Mallikarjun Chadalapaka
> Networked Storage Architecture
> Network Storage Solutions
> Hewlett-Packard MS 5668
> Roseville CA 95747
> cbm@rose.hp.com
> 
> 
> ----- Original Message -----
> From: "Eddy Quicksall" <Eddy_Quicksall@iVivity.com>
> To: "'Mallikarjun C.'" <cbm@rose.hp.com>; <ips@ece.cmu.edu>
> Sent: Monday, January 06, 2003 12:46 PM
> Subject: RE: iSCSI: Implicit Termination of Tasks
> 
> 
> > Yes, I noticed my typo of "two" vs. "three"
but too late.
> >
> > Below you say that the ordering is iSCSI ordering but section
6.5 is
> saying
> > SCSI ordering (queued commands is SCSI). So, that leaves me a
little
> > confused as to what this paragraph is trying to say, especially
when
> the
> > "status is never communicated back ... to the initiator".
> >
> > I'm probably mis-understanding something. It appears as 
> though this is
> just
> > a method of implementing within the target.
> >
> > Eddy
> >
> > -----Original Message-----
> > From: Mallikarjun C. [mailto:cbm@rose.hp.com]
> > Sent: Monday, January 06, 2003 3:12 PM
> > To: Eddy_Quicksall@ivivity.com; ips@ece.cmu.edu
> > Subject: Re: iSCSI: Implicit Termination of Tasks
> >
> >
> > Comments below.
> > --
> > Mallikarjun
> >
> > Mallikarjun Chadalapaka
> > Networked Storage Architecture
> > Network Storage Solutions
> > Hewlett-Packard MS 5668
> > Roseville CA 95747
> > cbm@rose.hp.com
> >
> > ----- Original Message -----
> > From: "Eddy Quicksall" <Eddy_Quicksall@ivivity.com>
> > To: <ips@ece.cmu.edu>
> > Sent: Monday, January 06, 2003 5:16 AM
> > Subject: iSCSI: Implicit Termination of Tasks
> >
> >
> > > There are two sections titled Implicit Termination of 
> Tasks but they
> > are
> > > slightly different. Which is correct?
> >
> > Both are correct and consistent.
> >
> > >
> > > Section 6.5 lists 4 items but section 10.14.5 only lists
two.
> >
> > I'm seeing three in 10.14.5.....
> >
> > Even though 6.5 lists all the four cases, it makes it clear that
the
> > check condition is to be employed only for three cases - and
> > only those three are listed by 10.14.5.  Perhaps the text
could have
> > been a little bit more explicit about this distinction.
> >
> > >
> > > If 6.5 is correct, why is item D not included in the unit
> attention?
> > SAM-3
> > > says:
> >
> > It's not so much a SAM issue.  The issue we considered was
how to
> ensure
> > iSCSI-standard ordered delivery of commands in the face of errors.
> The
> > ordered delivery of commands does not make sense for case (d)
- that
> of
> > creating a new session - ordering is not guaranteed anyway across
> > sessions.
> >
> >
>